1. SAFETY EQUIPMENT; Rules apply at all times car is on track. Snell rated SA2000 or SA2005 helmet required. (Effective January 1, 2008, SA95 helmets are no longer allowed.) Roll bar padding required in driver compartment (Fire retardant recommended). SFI-Approved full fire suit required. Fire retardant neck brace, gloves and shoes required. Recommended; fire retardant head sock and underwear, head and neck restraints, collapsible steering shaft. Driver side window net required, minimum 16”x20” ribbon or mesh style, and must be mounted so quick release latch is at top front of window. Minimum three inch wide SFI-approved five point safety belt assembly required. Y type shoulder harness not allowed. Must be mounted securely to roll cage. Recommended to be no more than one year old. Kill switch required within easy reach of driver and emergency personnel, must be clearly marked “Off and On”.
2. FRAME; 1978 to 1987 OEM midsize GM metric full frame only. Minimum wheel base 107”, maximum 109”. both sides. Frame must be full and complete. Can not be widened, narrowed, shortened, lengthened, or be cut, bent or altered to change suspension brackets, except upper control arm brackets on front end. All frame bolt holes must remain in OEM location. Front frame horns may be removed in front of steering box. Front frame may be cut for radiator clearance. Frame may be notched for seat clearance. Transmission cross member mounts may be removed, no further forward than frame welds. Rear of frame, behind upper shock mounts, may be replaced with round, square, or rectangular tubing. No part of the frame can be lower than five inches from ground except front cross member. No other frame alterations allowed.
3. ROLL CAGE; Must consist of continuous hoops, minimum 1.5 inch OD. Tubing, with a minimum wall thickness of .095 inch for main cage. Cage must be steel or chromemoly. Main cage no further forward than rear of engine and no further back than front edge of rear tire. Four bars, two per side, may extend from main roll cage to main frame points in front of upper control arms. These bars may have two additional braces per side to the main frame. Six bars may extend from the main cage to the rear. X bracing is allowed. Drivers head must NOT protrude outside cage with helmet on. Roll cage must be securely supported and braced with minimum one cross bar in top halo. All bars forward of cage must be lower than hood.
4. DOOR BARS; Minimum three drivers side door bars required, minimum 1.5” O.D. and .083 wall thickness, must be parallel to ground and perpendicular to driver, and welded to front and rear of roll cage. Minimum two passenger side door bars required, must have at least one cross door bar, horizontal or angled. Steel door plate 18 gauge or .049 inch minimum thickness must be securely welded to outside of drivers side door bars and cover area to protect driver.
5. BODY; (See diagram). Must be the same width, front to rear, and parallel to OEM frame. Engine compartment must remain open (no side panels). Aluminum or fiberglass hoods allowed, must completely cover top of radiator and engine, from nose to interior deck and enclosed at rear. Must have front and rear roof supports. Aluminum or fiberglass roofs allowed, must meet body diagram. No Gremlin roofs. No plastic body panels or filler panels allowed. Must have complete interior deck from side to side, must be aluminum or sheet metal. Quarter panels must remain 90 degrees to ground, maximum 45 degree bend 4 inches from bottom and 2 inches from top of doors and quarters. Rear spoiler may be maximum 8 inches in material height and maximum 67 inches wide. Spoiler may have stiffeners must be 1 inch or more down from top. Maximum 3 spoiler braces allowed, must be mounted in line. Spoiler braces must resemble all aspects of drawing. No fins, lips or wings allowed.
6. DRIVERS COMPARTMENT; Must have minimum three 5/16” inch O.D. windshield bars in front off driver. Aluminum cowl panel in front of driver can be no wider than cockpit. Aluminum high back racing seat only. Must be securely bolted, using 0.375 inch bolts, to roll cage and support system. Floor pan must be metal or aluminum and cover entire driver compartment. Bottom of seat can be no lower than bottom of frame rail. Driver must be sealed of from track, driveline, engine, fuel cell, canisters and pumps. No oil coolers in drivers compartment. No devices that would enable driver adjustments to alter wheel base or for weight jacking while car is in competition. No mirrors of any kind.
7. FRONT SUSPENSION; All components must be steel, unaltered OEM, in OEM location, and match frame. No jack bolts allowed. Adjustable spring buckets are allowed. Must use OEM upper and lower A-frames and mounts. OEM upper A-frame may be replaced using aftermarket upper A-frame (STEEL only), must display IMCA approved decal. Upper A frame mounts may be modified and moved for caster and camber adjustment, but must remain OEM material. Lower A frame mounts and bolts holes on frame must be in OEM location, mount may be notched for clearance. All A frame bushings may be aftermarket, but no bearing/heim type. OEM style ball joints only, may be tacked in. Sway bars (optional) and brackets must remain OEM.
8. STEERING; All components must be steel, unaltered OEM, in OEM location and match frame. No grinding, lightening, or welding on any steering parts. Spindles may be reamed and bolt on spindle savers are allowed. Steel steering shafts and knuckles only. Steering quickener (optional). Steering wheel and quick release (required) may be aluminum. Power steering pump and reservoir must remain one unit. Driver compartment steering may be modified, must be kept on left side. No rack and pinion.
9. SHOCKS; One steel shock per wheel only. Shock must be in OEM mounts and location, using OEM style shock. Mounting spacers and weld or screw on shock ends allowed. No air or coil over shocks, remote reservoir shocks. Schrader valves or bladder type valves allowed.
10. SPRINGS; One steel spring (racing allowed) per wheel only. Minimum 4.5 inches O.D., non progressive coils only. No torsion bars or air bags.
11. REAR SUSPENSION; All control arms and mounts must be steel, unaltered OEM, in OEM location, and match frame. No jack bolts allowed. Adjustable spring buckets allowed, may be dropped as long as they remain in OEM location. If upper spring cup uses all thread, it must be securely welded to chassis. Lower spring cups must be centered on housing. Control arms may be reinforced, but can not be shortened or lengthened, must remain OEM length. All control arm bushings may be aftermarket, but no bearing/heim type. Bushings cannot be drilled. No suspension parts may be altered or lightened. No aluminum parts allowed, other than bushings.
12. REAR END; Must use OEM 7.5 inch GM 10 bolt rear end (bracing optional) must remain stock width. No Ford or floater rear end allowed. Housing end, from control arm mount out, may be modified with 3 inch tubing to accept 9” inch Ford axle. If Ford axles are used, rear end must remain minimum GM width or maximum 3 inches wider. Steel components only. OEM mounts on lower control arms must remain in OEM location on original 7.5 inch tube housing. Aftermarket axles, mini spools and C clips eliminators allowed. Locked rear ends only, no torque dividing differentials allowed. No full or aluminum spools allowed. Pinion angle can not be changed. Any gear ratio allowed but housing must remain unaltered. No quick change devices.
13. BUMPERS/RUBRAILS; Steel only. Two bar front bumper and single bar rear bumper must be used on car at all times and welded, or bolted securely. Must be a maximum 1.50 inch O.D. tubing, .095 inch wall thickness on front and 1.75 inch tubing .095 wall thickness on rear. Maximum 1.50 inch O.D. tubing, .095 inch wall thickness fuel cell protection bar required, must cover rear and extend past both sides of call, may be welded to rear bumper. See diagram for bumper heights. Rear bumper may be maximum 6” inches beyond rear deck. All bumpers and rub rails must be capped with no sharp edges. Single bar rub rail from front to rear wheel allowed on each side, no center supports allowed, maximum 1.50 inch O.D. tubing and .095 inch wall thickness, must be mounted to cage at front and rear of rub rail.
14. TIRES/WHEELS; May use Hoosier 500 8” inch racing tires 27x8x15, or 26.5x8x15 stagger tire allowed. or 8” asphalt scuffs. No siping of any tires allowed, (see rule book for automatic penalties.) Grooving allowed. No recaps. Any offset allowed. May use bead lock on right rear only. External bead lock only and it cannot make wheel any narrower than 8 inches and no wider than 8.75 inches. Steel bolts only. Inner mud cover allowed on left rear only. No bleeder valves. Must use minimum 1 inch O.D. lug nuts and 0.625 inch studs are recommended. No wheel spacers allowed with OEM studs. Wheel adapters are treated as spacers and may be aluminum, maximum 1.50 inch thick.
15. BRAKES; Must be steel OEM, operative three wheel, drum or disc. Must maintain minimum OEM dimensions for hubs, rotors and calipers, cannot be lightened. Bolt pattern may be changed. 0.625 inch studs allowed. Single or dual aftermarket master cylinders allowed. Drivers adjustable dual pedal brake bias allowed. Additional proportioning valve (in line) allowed, must be out of drivers reach. Rear rotors may be aftermarket, minimum 0.810 inch thickness, maximum 12 inch O.D.. Vented rotors only, no scalloped, ceramic coated, single phase or drilled rotors allowed. Rear caliper brake brackets must be welded to housing.
16. EXHAUST; Must use Schoenfeld headers. GM: #161, #151, #151E with 1.625 inch tubes and 3 three inch collectors. Chrysler: #461, 461W2, #462W2. Ford: #361, #362, #562, #562-4B, #563-4B. No header modifications allowed. Coated headers allowed. No exhaust sensors allowed, merge collectors, cross overs, turn outs of balance tubes allowed.
17. FUEL SYSTEM; Racing fuel cell required, maximum 22 gallons capacity. Must be in minimum 20 gauge steel container. Must be securely mounted, with minimum 2 steel straps around entire fuel cell, between frame rails in trunk area only. Fuel cell vents, including cap vent, must have check valves. If fuel cell does not have aircraft style positive seal filler neck/cap system - a flapper, spring or ball type filler roll over valve is required. No part of cell can be lower than protective tubing. OEM mounted, mechanical push rod fuel pumps only. No regulators, bypass systems, pressurized, or return lines allowed. CARBURETOR (one only): Holley (unaltered) #4412 or #0-80583-1, 500 cfm two barrel may be used on any engine. OEM GM Quadrajet or two barrel may be used on Chevy. OEM Motorcraft four or two barrel may be used on Ford. OEM Carter or AFB four or two barrel may be used on Chrysler. OEM carburetors must remain unaltered, circle track floats may be installed. No other carburetor allowed. Adapter/spacer allowed, maximum 1.250 inches thick, including gaskets. No drivers compartment adjustable carburetors or spacers. Limit one fuel filter. No cool cans. Any air cleaner allowed. No cold air boxes allowed.
18; FUEL; Gasoline only. Racing fuel allowed. NO performance enhancing additives or scents additives allowed. Fuel must pass dialectric meter and chemical tests. Fuel sample may be taken from any car at any time (see rule book for automatic penalties).
19. WEIGHT: Minimum weight limit of 2350 LBS. after race with driver in car. Weights must not be used in drivers compartment or on outside of body. All weights must be securely mounted with at least two .5 inch bolts, painted white with car number on it. No titanium, magnesium, stainless steel, or carbon fiber components. Solid steel fasteners only.
20. BATTERY/STARTERS; One 12 volt battery only. Must be shielded and securely mounted. Aftermarket starter allowed, must bolt in OEM location. Must have capability of starting without being pushed or pulled. Must leave initial staging area on demand, unaided, or go to rear of race.
21; GAUGES/ELECTRONICS; No unapproved cameras, transmitting or listening devices, timing retard controls , or digital gauges (including tach). No electronic monitoring computer devices capable of storing or transmitting information except analog tach. OEM style ignitions only. GM: HEI distributor (must remain one unit) or point distributor allowed. Ford/Chrysler: May use OEM ignition, including OEM boxes, or HEI distributor. Any module may be used that fits inside the distributor with no alterations. Vacuum advance may be removed and pick up coil locked. No external coils allowed, unless using point distributor. No GM or aftermarket ignition boxes allowed. No electronic traction control devices (see rule book for automatic penalties).
22. TRANSMISSION/DRIVESHAFT; Only OEM production transmission allowed. No aftermarket transmissions allowed. No in and out boxes or quickchange devices allowed. With engine running and car in a still position, must be able to engage car in gear and move forward, then backward. Functioning shift levers must be in OEM location. Transmission fluid coolers allowed. Flywheel, flex plate and converter must be steel.
Automatic; Any automatic OEM transmission allowed. Must use functioning, minimum 10” inch diameter steel torque converter. No direct drives, couplers, valve pumps, or bleeder style valve bodies. Must have at least one forward gear and reverse gear, gears must function. Must have approved scatter shield constructed of .125 inch by three inch steel, 270 degrees around top of flex plate. GM automatic must be used with GM engine, may be used with Ford or Chrysler engines. Stall converters allowed. Steel OEM style flex plate only, must be bolted directly to end of crankshaft.
Manual; 3,4, or 5 speed OEM manual transmission only. All gears must function. Must have functioning 10.5 inch minimum diameter clutch and pressure plate bolted directly to steel flywheel. These components must rotate, consistent with engine rpms, while car is in any gear. Must have explosion proof steel bell housing 180 degrees around top of clutch and flywheel. No mini clutches or couplers. Minimum 9” inch Ford clutch allowed. Hydraulic slave cylinder/ throw out bearing allowed.
Drive shaft; Minimum 2’ inch diameter, white, steel driveshaft only. Steel slip yokes only. 360m degree drive shaft loop required, constructed of at least 0.125 inch by 2” inch steel, or 1” inch tubing, mounted 6” inches back from front of u-joint.
23. ENGINE COMPARTMENT; Rear of engine (bell housing flange) must be mounted at least 70” inches forward from centerline of rear axle. Minimum 11” inch engine height from ground to center of crankshaft. One radiator allowed, steel or aluminum, 27” inches by 19” inches maximum in size, must be mounted in front of engine. Racing cap and electric fans allowed. No sprinklers. Catch can required. Power steering pump and reservoir must remain as one unit and be mounted to the front of engine. Side engine mounts (OEM or 45 degree style) must be steel. Aluminum midplate allowed.
24. ENGINE SPECIFICATIONS; Must use OEM cast iron, American make V-8 small block engines only. No Bowtie, SVO, or W-2 components allowed. All engines must be able to be used in conventional passenger car without alterations. External engine casting and threaded holes cannot be altered. No aluminum, titanium or carbon fiber components allowed.
BLOCK; GM (Chevy only): 283, 302, 305, 307, 327, 350. Ford: 260, 289, 302, 351. Chrysler: 273, 318, 340, 360. No hemis. Maximum cubic inch limits: GM 364 c.i., Ford: 360 c.i., Chrysler: 370 c.i., no tolerance. No 400 or larger cubic inch parts allowed. Flat top or dish cast pistons only. Chevy must use four valve relief. No gas ported or floating pistons. 3.48” inch maximum GM stroke. Maximum 175 pounds per cylinder compression, no tolerance. Compression checked with one spark plug removed, turned five engine revolutions. Engines may be balanced and block decked. Oil filter system must remain OEM. Wet sump oiling system only. No accusumps. OEM rods. Chevy must use maximum 5.7 inch rod. Steel or cast OEM crank shafts only. No splayed main caps. Racing oil pans allowed. One inch inspection hole recommended in pan, no obstructions to crank and rods. If obstructions are present, must remove pan for inspection. Engine bolts may be aftermarket. Fluid dampener balancer allowed. No roller bearings allowed.
INTAKE: Unaltered, approved OEM cast iron low rise. Two or four barrel: or unaltered Weiand aluminum- IMCA stamped, Chevrolet, # 7547-1, Ford: 302 #7515, 351 Windsor #8023, 351 Cleveland #7516, Chrysler: #7545. No porting, polishing, or alterations of any kind, including cooling lines or plenum alterations to ANY intake. No OEM highrise, marine or bowtie intakes. Ford may use OEM aluminum intake, no under air or highrise. All intakes must have unobstructed 0.250 inch vacuum fitting. Belt driven, OEM style water pumps only. No aluminum water pumps on Chevy engine.
CAMSHAFT; Non roller hydraulic cam/lifters only. Hydraulic lifters must remain unaltered OEM. No maximum cam lift. Must pull 12 inches of vacuum at 1200 rpms. Vacuum to be pulled at intake vacuum fitting, not carburetor. NO alterations of any kind may be made at time of tech. Track equipment being used for tech is final. Lifter for bores cannot be altered. Must be chain driven. No gear or belt drives.
CYLINDER HEADS: Only GM OEM approved head numbers are, (last three digits) : 126, 185, 336, 441, 445, 487, 493, 598, 624, 862, 882, 920, 993, 997, with valves no larger than 1.94 inch intake and 1.50 inch exhaust. May use Engine Quest (EQ) Stock Replacement (SR) cylinder head, part number CH3501, head must remain as produced valve sizes cannot be changed, No porting, polishing or unapproved alterations to ANY cylinder head. Any cast iron OEM Ford and Chrysler OEM heads allowed with valves no larger than 2.04 inch intake and 1.70 inch exhaust. Headers must bolted directly to heads with correct numbers. No vortec, Bowtie, SVO, W-2 or aftermarket heads allowed. Flat milling allowed. Guide plates, screw in shouldered studs (0.375 inch maximum) and polylocks allowed, no stud girdles. Stamped steel, OEM style, stud mounted(0.375 inch maximum) rocker arms allowed. Chrysler may use OEM rocker arm bars. Any length push rods allowed. OEM diameter springs must match heads (no beehive valve springs allowed.)
25. ENGINE CLAIMING RULES; Refer to 2008 rule book for claim eligibility requirements.
A. $500.00 cash and exchange claim on engines, $50.00 goes to Enid Speedway Park for pulling engines.
B. Claim does not include 1. Flywheel 2. Clutch 3. Pressure plate 4. Bell housing 5. Breathers 6. Carburetor 7. Starter 8. Motor mounts 9. Oil/temp. sending units 10. Water fan and pulleys 11. Clutch ball 12. Clutch arm 13. Throw out bearings 14. Dip stick 15. Water pump 16. Fuel pump, rod and plate 17. Distributor 18. Plug wires 19. Water outlet and restrictors 20. Headers.
NOTE: During engine claim, inspect heads and intake, and one spark plug must be removed to check pistons prior to transfer of engines. If at this time, an engine is found illegal, driver is disqualified and suspended for two weeks of race events at Enid Speedway Park, for first offense. Exchange of engines may proceed depending on circumstances. Decision to proceed is at discretion of track officials.
26. ENGINE PROTEST PROCEDEURES: Within 5 minutes after race, any driver starting feature, may for $250.00, protest any engine. $50.00 of protest fee goes to track and will not be refunded regardless of outcome of protest. Driver may not protest another driver finishing in a position behind them and may not protest same driver more than once per calendar year. Under this protest, following MUST be inspected: intake manifold, cylinder heads (removal required), stroke, and visual inspection of crank shaft (pan may removed). $200.00 will be returned to protester if engine is found illegal. If engine is found legal, $200.00 protest fee will be paid to the driver being protested. If parts are found illegal, or if driver refuses to submit to protest, first infraction will result in forfeiture of all cash, contingences, trophies and points earned that night.
27. EIRI; (Except in rare instances) Decisions of officials are final and binding without exception. In some cases track safety rules may take precedence over these written rules.
REMEMBER IF DOES NOT SAY YOU CAN…YOU CAN’T.
PROMOTER RESERVES THE RIGHT TO CHANGE OR CLARIFY ANY RULES TO IMPROVE COMPETITION, SAFETY OR COST.